Welcome to Würth Finland For trade customers only
Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5 Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5 Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5
Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5 - 1
Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5 - 2
Angle bracket type A - ANGL-WOCON-A-BAR-90X90X65X2,5 - 3

Angle bracket type A

Angle connector, type A with web
ANGL-WOCON-A-BAR-90X90X65X2,5

Art.-no. 0681090965
EAN 4052703996469
All versions

-

Show availability at another Würth Center
Exclusively for trade customers

Register and access more than 75 000 products

Angle brackets A with reinforcement rib are ideal for high-quality load-bearing wood/wood and wood/concrete connections in timber construction. Universally suitable for standard connections such as intersecting timbers.
  • Sheet metal hot-dip galvanised on both sides (DX51D + Z275 [approx. 20 µm]) in line with EN 10327:2004

  • Application in utilisation classes 1 and 2 in line with EN 1995:2013
Proof of Performance

European Technical Approval ETA-09/214

Notice

The transverse load of the connected timbers must be observed and verified where necessary. Transverse reinforcement can be added using ASSY plus VG full-thread screws.



Diameter of bolt/screw/metal anchor may only be max. 2 mm smaller than the diameter of the hole.



Load tables and detailed processing instructions can be found on the service page www.wuerth.de/holzverbinder.

Application area

European Technical Approval ETA-09/214

Product information

Würth Oy Catalogue

Datasheets(X)

Certificates/ Documents / additional info

 | 

 | 

Click here for the complete CAD library
Application area

Load-bearing connections of timber joists to wood such as joist to joist and purlin to joist.

Instructions

Suitable fasteners:


  • Ring-shank/ribbed nail in line with EN 14592: 4.0 x 40 mm

  • ASSY 3.0 Combi in line with ETA 11/0190: d = 12 mm

  • Bolts and metal anchors in accordance with manufacturers' specifications: d = 12 mm

Type

A

Width x height x depth

65 x 90 x 90 mm

Thickness

2.5 mm

Design

With bar

Number of D 13 mm holes in subcarrier nJ/main carrier nH

1 + 1 PCS

Number of D 5 mm holes in subcarrier nJ + main carrier nH

10 + 10 PCS

Approval

ETA-09/0214

Product weight (per item)

202.520 g

Material

Steel

Surface

Hot dip galvanized

Weight

197 g

Material designation

DX51D

Material standard

DIN EN 10327:2004

Number of D 5 mm holes

20 PCS

Number of D 13 mm holes

2 PCS

Characteristic load-bearing capacities in kN;
1 piece angle bracket type A with Würth ring-shank nails
Angle bracket type A
Article numberETAAnchor nail in 1 angle bracket type A for each connection 3)
F1,RkF2/3,RkF4,RkF5,Rk
Width x length x depth in mm WoodSteelWoodWoodSteelWoodSteel
55x70x70x2.50681 070 05509/02144x401,580,922,90------------
65x90x90x2.50681 090 06509/02144x402,501,383,67------------
90x105x105x3.00681 100 09009/02144x403,762,285,94------------
55x70x70x2.55390 200 07008/01834x401,530,783,79------------
65x90x90x2.55390 200 09008/01834x604,041,174,78------------
90x105x105x3.05390 200 10508/01834x604,052,256,40------------
With rib65x90x90x2.50681 090 96509/02144x401,253,153,537,033,661,981,17
90x105x105x3.00681 100 99009/02144x402,517,915,069,969,212,954,82
55x70x70x2.55390 201 07008/01834x401,582,292,75The load-bearing capacity depends on the geometry of the connected component 4), see tables F4 and F5
65x90x90x2.55390 201 09008/01834x603,234,304,20
90x105x105x3.05390 201 10508/01834x605,907,004,80
55x70x70x1.55390 202 07008/01834x605,40---6,35------------
65x90x90x1.55390 202 09008/01834x604,90---6,10------------
90x105x105x1.55390 202 10508/01834x609,20---8,50------------
mmkNkNkNkNkNkNkN
Without rib35x50x50x2.50681 050 04009/02164x401.101)0.921)1,31------------
40x90x90x3.00681 090 04009/02164x401,211,142,40------------
3) If one angle bracket is used for each connection, the connected component must be secured against twisting.
4) The loads F4 and F5 act on the top edge of the connected component. Securing against twisting is not required.
The specified load-bearing capacities apply to softwood at 350 kg/m³ ≤Ƥk ≤420 kg/m³.
For woods with 290 kg/m³ ≤ Ƥk ≤ 350 kg/m³, the specified load-bearing capacities for wood must be multiplied by the factor kdens:
tSteel ≥ 2.5 mm: kdens = (pk/350)^2
tsteel = 1.5 mm: kdens= (pk/350)^0.8
Design values of the load-bearing capacities: Fi,Rd = min {Fi,wood,Rd; Fi,steel,Rd}
Failure of fasteners in wood: Fi,Wood,Rd = kmod/ƳM,Wood × Fi,Wood,Rk with ƳM,Wood = 1.3
Steel failure of the connector: Fi,steel,Rd = Fi,steel,Rk/ƳM,steel with ƳM,steel = 1.25
For several simultaneous loads, the following condition must be met:


The specified nailing patterns must be observed in accordance with the relevant ETA.
PLEASE NOTE: These are guides for planning purposes. The values must be calculated for each project by authorised persons.
Characteristic load-bearing capacities in kN;
1 piece angle bracket type A with Würth ring-shank nails
Angle bracket
Width b in cmHeight h in cm
81012141620
Table F4F4,Wood,Rk ; F4,Steel,Rk in kN4)
Table F5:F5,Wood,Rk; F5,Steel,Rk in kN4)
55x70x70x2.5 mm (Art. no. 5390 201 070)61.58; 0.931.73; 1.12---2.45; 1.06------
101.44; 1.301.58; 1.19---1.56; 1.26------
141.45; 1.291.47; 1.28---1.48; 1.26------
65x90x90x2.5 mm (Art. no. 5390 201 090)8------3.85; 1.834.24; 1.724.89; 1.62---
10------3.49; 1.983.65; 1.903.88; 1.82---
14------3.23; 2.123.30; 2.083.37; 2.03---
90x105x105x3.0 mm (Art. no. 5390 201 105)8------5.94; 3.14---5.45; 2.674.68; 2.30
10------5.24; 3.55---6.09; 3.135.27; 2.80
14------4.68; 3.99---5.00; 3.725.35; 3.47
Height h in cm81012141620
55x70x70x2.5 mm
(Art. no. 5390 201 070)		0.82; 0.380.66; 0.28
---0.47; 0.21
---
---
65x90x90x2.5 mm
(Art. no. 5390 201 090)		---
---1.11; 0.46
0.95; 0.40
0.84; 0.35
---
90x105x105x3.0 mm
(Art. no. 5390 201 105)		---
---2.42; 1.02
---1.82; 0.69
1.37; 0.52
3) If one angle bracket is used for each connection, the connected component must be secured against twisting.
4) The loads F4 and F5 act on the top edge of the connected component. Securing against twisting is not required.
For woods with 290 kg/m³ ≤ Ƥk < 350 kg/m³, the specified load-bearing capacities for wood must be multiplied by the factor kdens:
tSteel ≥ 2.5 mm: kdens = (pk/350)^2
tSteel = 1.5 mm: kdens = (pk/350)^0.8
Design values of the load-bearing capacities: Fi,Rd = min {Fi,wood,Rd; Fi,steel,Rd}
Failure of fasteners in wood: Fi,Wood,Rd = kmod/ƳM,Wood × Fi,Wood,Rk with ƳM,Wood = 1.3
Steel failure of the connector: Fi,steel,Rd = Fi,steel,Rk/ƳM,steel with ƳM,steel = 1.25
For several simultaneous loads, the following condition must be met:

The specified nailing patterns must be observed in accordance with the relevant ETA.
PLEASE NOTE: These are guides for planning purposes. The values must be calculated for each project by authorised persons.
Characteristic load-bearing capacities in kN;
2 piece angle bracket type A with Würth ring-shank nails
Angle bracket type AArticle numberETAAnchor nail2 angle brackets type A for each connection
Width x length x depthF1,RkF2/3,RkF4/5,Rk2)
WoodSteelWoodWoodSteel
(mm)kNkNkNkNkN
65x90x90x2.50681 090 06509/02144.0x405,002,777,347,824,45
90x105x105x3.00681 100 09009/02144.0x407,524,5511,909,308,46
55x70x70x2.55390 200 07008/01834.0x403,051,567,576,103,63
65x90x90x2.55390 200 09008/01834.0x608,072,349,559,673,99
90x105x105x3.05390 200 10508/01834.0x608,094,5012,8010,607,98
With rib65x90x90x2.50681 090 96509/02144.0x402,506,317,067,034,17
90x105x105x3.00681 100 99009/02144.0x405,0115,8010,109,9613,10
55x70x70x2.55390 201 07008/01834.0x403,164,575,495,654,12
65x90x90x2.55390 201 09008/01834.0x606,468,598,398,916,55
90x105x105x3.05390 201 10508/01834.0x6011,8014,009,6011,9011,80
55x70x70x1.55390 202 07008/01834.0x6010,80---12,7011,00---
65x90x90x1.55390 202 09008/01834.0x609,80---12,2013,50---
90x105x105x1.55390 202 10508/01834.0x6018,40---17,0016,40---
Without rib35x50x50x2.50681 050 04009/02164.0x402.191)1.841)2,636,992,00
40x90x90x3.00681 090 04009/02164.0x402,412,284,804,134,28
55x70x70x2.50681 070 05509/02144.0x403,151,845,805,344,34
1) Only for purlin connections.
2) For the load F4/5, the additional force ΔF1,d = F4/5,d × e/b must be taken into consideration.
The specified load-bearing capacities apply to softwood at 350 kg/m³ ≤Ƥk ≤420 kg/m³.
For woods with 290 kg/m³ ≤ Rk < 350 kg/m³, the specified load-bearing capacities for wood must be multiplied by the factor kdens:
tSteel ≥ 2.5 mm: kdens= (pk/350)^2

tSteel = 1.5 mm: kdens = (pk/350)^0.8

Design values of the load-bearing capacities: Fi,Rd = min {Fi,wood,Rd; Fi,steel,Rd}
Failure of fasteners in wood: Fi,Wood,Rd = kmod/ƳM,Wood × Fi,Wood,Rk with ƳM,Wood = 1.3
Steel failure of the connector: Fi,steel,Rd = Fi,steel,Rk/ƳM,steel with ƳM,steel = 1.25
For several simultaneous loads, the following condition must be met:

The specified nailing patterns must be observed in accordance with the relevant ETA.
PLEASE NOTE: These are guides for planning purposes. The values must be calculated for each project by authorised persons.
Required accessory:
 
Product
Description
Quantity
PU
Price
/PU

SCR-WO-HEX-AW40-(A3K)-12X100/60

ASSY 3.0 KOMBI
For powerful steel/wood and wood/wood screw connections with U washers, in particular for the timber construction and carpentry sector.
x 50 pcs

RIDGNL-(A3K)-4X40MM

Galvanised steel, blue coated (A2K)
x 250 pcs

RIDGNL-(A3K)-4X50MM

Galvanised steel, blue coated (A2K)
x 250 pcs

RIDGNL-(A3K)-4X60MM

Galvanised steel, blue coated (A2K)
x 250 pcs

ANC-(W-FAZ/S)-(A2K)-125-M12X220

Bolt anchor for high loads in cracked and non-cracked concrete. Steel, zinc-plated
x 25 pcs

ANC-(W-FAZ/S)-(A2K)-145-M12X240

Bolt anchor for high loads in cracked and non-cracked concrete. Steel, zinc-plated
x 20 pcs

ANC-(W-FAZ/S)-(A2K)-160-M12X255

Bolt anchor for high loads in cracked and non-cracked concrete. Steel, zinc-plated
x 20 pcs
The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.
The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076
Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Würth Oy Catalogue

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents / additional info

 | 

 | 

Technical information
Show all product details