Welcome to Würth Finland For trade customers only

Tapping and chipping hammer BMH 45-XE

Hammer drill/chipping hammer, BMH 45-XE, low-vib.
HAMDRLCHPNGHAM-EL-(BMH 45-XE)

Art.-no. 07025571

EAN 4053479221502

-
Tapping and chipping hammer BMH 45-XE

Art.-no. 07025571

-
Quantity
PU
x 1 pcs

Show availability at another Würth Center
Exclusively for trade customers

Register and access more than 75 000 products

Powerful and anti-vibration 8-kg hammer drill/chipping hammer with SDS-max drive arbour.

Comfortable working


No need to hold switch continually during prolonged chiselling work.



Adjustable drilling and impact power


The power can be reduced or increased by simply turning the electronic adjusting wheel.



Indication of malfunctions


The service LED indicates malfunctions and an imminent carbon brush replacement.



Rapid drilling progress and extremely smooth running


The anti-vibration system protects the user's joints. Shorter drilling times with high impact power.



Low-fatigue work


The 12 lockable chisel settings allow adjustment to any working angle.

3 Years Warranty on manufacturing and material defects


Excluded are damages caused by improper use, overloading or failure to observe the operating instructions.

Product information

Datasheets(X)

Certificates/ Documents

 | 

 | 

Nominal voltage

230 V/AC

Frequency

50 Hz

Protection class

Protection class II/protective insulation

Power input

1500 W

Power output

810 W

Min./max. idle speed

0-305 rpm

Min./max. impact rate

1380-2760 rpm

Tool holding device

Suitable for SDS-max

Impact energy

12.5 J

Min./max. drilling diameter in concrete

12-45 mm

Min./max. recommended drilling range for optimum performance (in concrete)

20-40 mm

Max. drilling diameter of breakthrough drill in concrete

80 mm

Max. drilling capacity (volume) in concrete per minute

221 cm³

Max. chiselling power in concrete

250 kg/h

Max. drilling diameter of hollow drill bit in masonry

125 mm

Weight of machine

8.9 kg

Cable length

4 m

Tapping and chipping hammer BMH 45-XE including:
Handle
1 x
Handle

SP-AUXILIARY HANDLE

Quantity: 1 x
1 x
Maintenance spray

MAINTSPR-CONCENTRATE-100ML

Description:
100 ml
For lubricating hinges, tool mounts and machine mounts
Quantity: 1 x
Machine case
1 x
Machine case

SP-CASE

Quantity: 1 x
The packaging size is determined on a product-specific basis, either as a full package or as individual items.
The item number contains at least 10 and at most 18 characters.
Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
The quantity of the product according to packaging size or pieces.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).
Additional accessory:
 
Product
Description
Quantity
PU
Price
/PU
Point chisel with SDS-max drive arbour

PTCHIS-MAX-L400MM

For general demolition and breaking-through work
x 1 pcs
Flat chisel with SDS-max drive arbor

FLCHIS-MAX-L400-W25MM

Round shaft for general demolition and break-through work
x 1 pcs
The packaging size is determined on a product-specific basis, either as a full package or as individual items.
The item number contains at least 10 and at most 18 characters.
Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
The quantity of the product according to packaging size or pieces.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information